HomeBoat PaintNon-slip PaintNON-SLIP Marine Boat Gloss Paint for Fibreglass and GRP 750ml – 1 litre

NON-SLIP Marine Boat Gloss Paint for Fibreglass and GRP 750ml – 1 litre

£13.32£18.99 Ex VAT

Description

NON-SLIP Supplyshed Marine Gloss Paint for Fibreglass / GRP

  • This high quality gloss formulation has been tried and tested for over twenty years.
  • Leaves a very durable high gloss finish roughened with embedded granules to protect against slips
  • Can be applied with a brush, or roller.
  • Suitable for above waterline use only. Interior & exterior use
  • Over covers most other paint types, for best results use a undercoat.
  • White spirit based for easy brush cleaning
  • Exceptionally good value – manufactured exclusively for the internet NO middle men taking extra margins!
  • Other NON-SLIP colours available to match our gloss paint range
  • Quantity discounts given.
  • 5 litre tins available telephone 01948 664071 for more info.

Undercoats

To get the best out of your paint we recommend that you use the most suitable undercoat per colour in preparation. Please see below:

  • Black Paint – use grey undercoat
  • White Paint – use white undercoat
  • Wine Red – use poppy red undercoat
  • Signal Red – use poppy red undercoat
  • Summer Yellow – use satinwood undercoat
  • JCB Yellow – use satinwood undercoat
  • Cream – use satinwood undercoat
  • Lt Brunswick green – use grey undercoat
  • Brunswick / British Racing Green – use grey undercoat
  • Oxford Blue – used grey undercoat
  • Royal Blue – use grey undercoat
  • Midnight Blue – use grey undercoat
  • French Blue – use grey undercoat
  • Aquamarine – use white undercoat
  • Lt Admiralty – use grey undercoat

Data

A high quality finish designed for application to super structures and deck fittings over Supplyshed Marine Undercoat 229. It is non-yellowing and highly resistant to weather, sunlight and salt spray. Marine Gloss is suitable also for use on interior surfaces in accommodation areas, alley ways, galleys, etc. Colour: See BS4800 Colour Card. See Health and Safety Precautions.

Drying Times @ 20 OC:
Surface Dry: 4 hours
Hard Dry: 12 hours Overcoating: 16 hours

Covering Capacity
Theoretical: In range 10.3 – 17.2 sq. metres per litre, depending on colour and film thickness.
Practical: Figures will be lower and will depend on the type of structure, application techniques and prevailing conditions.
Wet Film Thickness: 61-93 microns
Dry Film Thickness: 25-38 microns

Solids by Volume: 39 – 44% according to colour.

Flash Point: >41OC

Thinners: TH1 Cleaning Solvent: White Spirit Substrates: Suitably primed steel or wood.

PLEASE NOTE: The above figures are given as a guide only and may vary with temperature and method application.

Health & Safety Precautions
Toxicity: The solvent vapour is not highly toxic but inhaling the vapours, particularly in enclosed situations, can result in giddiness or nausea. The effects are temporary and avoided by adequate ventilation.
Care must be taken to avoid ingestion of the paint. This can result in a cumulative poisoning effect. When using, operatives should not eat, drink or smoke. Hands should be washed very thoroughly before food or drink is consumed. If the paints are applied by spray, operatives must be adequately protected.
Fire Risk: The vapours are flammable and no naked lights of any kind can be allowed in the vicinity.

SMOKING MUST BE PROHIBITED ** These figures are given as a guide only and may vary with temperature and method of application. The information contained herein together with the suggestions for use and application is, to the best of our knowledge, true and reliable. Since conditions of application and use are beyond our control, no warranty is expressed or implied in respect of these recommendations or products. Users are recommended to carry out confirmatory tests to check the suitability of products for their specific use. PJM1299/

How to Apply

Application
Brush or Roller. NOT SUITABLE FOR SPRAYING

Surface Preparation
Steel: Surfaces should be thoroughly wire brushed to remove all dirt, rust, loose and flaking paint. The surface should be thoroughly degreased prior to application of any paint. Sound paint, if glossy, should be matted down and edges levelled off. Areas of bare metal should be given one coat zinc phosphate primer TDS463 or unidox primer for steelwork TDS 173. When this is hard dry the entire surface should be given one coat of marine undercoat 229, followed by one coat of supplyshed marine gloss.

Light Alloy: Surfaces should be wire brushed to remove all dirt, loose and flaking paint. Sound paint surfaces, if glossy, should be matted down and edges bevelled off. Areas of bare metal should be given one coat of etch primer followed by Supplyshed marine undercoat 229 over the entire surface, followed by the coat of Supplyshed Marine Gloss 230.

Wood: Surfaces should be scraped to remove dirt and loose and flaking paint. Sound painted areas should be well matted down and edges bevelled off. Areas of bare wood should be given one coat of Primer for wood, TDS 153. The entire surface should then be given one coat of Supplyshed Marine Undercoat 229, followed by one coat of Supplyshed Marine Gloss.

Reviews

There are no reviews yet.

Be the first to review “NON-SLIP Marine Boat Gloss Paint for Fibreglass and GRP 750ml – 1 litre”

Your email address will not be published. Required fields are marked *

You may also like…